55.100 (Bottles. Pots. Jars) 标准查询与下载

ASTM F2013-10 用自动静态顶部空间取样设备和带火焰电离检测器的毛细管GC测定聚乙烯对苯二甲酸酯瓶装聚合物中残留乙醛的标准试验方法

This test method is of particular use as a quality control tool for a molding or synthesis operation. Acetaldehyde is a volatile degradation product generated during melt processing of PET. Thus, it becomes trapped in the sidewalls of a molded article and desorbs slowly into the contents packaged therein. In some foods and beverages AA can impart an off-taste that is undesirable, thus, it is important to know its concentration in PET articles that are to be used in food contact applications. The desorption conditions of 150 C for 60 min are such that no measurable AA is generated by the sample during the desorption process.1.1 This test method covers a gas chromatographic procedure for the determination of the ppm residual acetaldehyde (AA) present in poly(ethylene terephthalate) (PET) homo-polymers and co-polymers which are used in the manufacture of beverage bottles. This includes sample types of both amorphous and solid-stated pellet and preform samples, as opposed to the bottle test, Test Method D4509, an acetaldehyde test requiring 24 h of desorption time at 23°C into the bottle headspace and then the concentration of the headspace quantified by a similar GC method. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Residual Acetaldehyde in Polyethylene Terephthalate Bottle Polymer Using an Automated Static Head-Space Sampling Device and a Capillary GC with a Flame Ionization Detector

ASTM D4267-07 小容积(100毫升或低于100毫升)非肠道药物包装容器用标签的标准规范

1.1 This specification covers the orientation, the size of type used, and the contrast of the copy with the label background on immediate drug containers having a volume of 100 mL or less.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Labels for Small-Volume (100 mL or Less) Parenteral Drug Containers

ASTM D3844-02 氯代烃类溶剂容器的标记用标准指南

1.1 This guide is intended to provide industrial health and safety labeling for the following chlorinated hydrocarbon solvents: methylene chloride, perchloroethylene, and trichloroethylene. Additional labeling may be required if other chemicals are mixed with these solvents, or if special containers (for example, aerosol packages) are employed.

Standard Guide for Labeling Halogenated Hydrocarbon Solvent Containers

ASTM F2013-01 用自动静态顶部空间取样设备和带火焰电离检测器的毛细管GC测定聚乙烯对苯二甲酸酯瓶装聚合物中残留乙醛的标准试验方法

1.1 This test method covers a gas chromatographic procedure for the determination of the ppm residual acetaldehyde (AA) present in poly(ethylene terephthalate) (PET) homo-polymers and co-polymers which are used in the manufacture of beverage bottles. This includes sample types of both amorphous and solid-stated pellet and preform samples. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Residual Acetaldehyde in Polyethylene Terephthalate Bottle Polymer Using an Automated Static Head-Space Sampling Device and a Capillary GC with a Flame Ionization Detector

ASTM F2013-00 用自动静态顶部空间取样设备和带火焰电离检测器的毛细管GC测定聚乙烯对苯二甲酸酯瓶装聚合物中残留乙醛的标准试验方法

1.1 This test method covers a gas chromatographic procedure for the determination of the ppm residual acetaldehyde (AA) present in poly(ethylene terephthalate) (PET) homo-polymers and co-polymers which are used in the manufacture of beverage bottles. This includes sample types of both amorphous and solid-stated pellet and preform samples. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Residual Acetaldehyde in Polyethylene Terephthalate Bottle Polymer Using an Automated Static Head-Space Sampling Device and a Capillary GC with a Flame Ionization Detector

ASTM D3844-96 卤化烃溶剂容器标记的标准指南

1.1 This guide is intended to provide health and safety labeling for the following chlorinated hydrocarbon solvents: methylene chloride, perchloroethylene, 1,1,1-trichloroethane, and trichloroethylene. Additional labeling may be required if other chemicals are mixed with these solvents, or if special containers (for example, aerosol packages) are employed.

Standard Guide for Labeling Halogenated Hydrocarbon Solvent Containers

ASTM D4267-95(2001) 小容积(100毫升或低于100毫升)非肠道使用的药物包装容器用标签的标准规范

1.1 This specification covers the orientation, the size of type used, and the contrast of the copy with the label background on immediate drug containers having a volume of 100 mL or less. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Labels for Small-Volume (100 mL or Less) Parenteral Drug Containers

ASTM D4316-95(2005) 弹性水瓶标准规范

1.1 This specification covers requirements for molded, non-fabric reinforced, elastomeric water bottles with closure and screw stopper, generally used with hot or cold water in personal hygiene and health care. 1.2 The safe and proper use of elastomeric water bottles is beyond the scope of this specification except for the user instructions in 9.2.

Standard Specification for Elastomeric Water Bottles

ASTM D2741-95(2001) 聚乙烯塑料瓶对烟灰存积敏感性的标准试验方法

1.1 This test method covers the determination of the relative susceptibility of polyethylene bottles to soot accumulation. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.Note 1--There is no similar or equivalent ISO standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 8 and Note 7.

Standard Test Method for Susceptibility of Polyethylene Bottles to Soot Accumulation

ASTM D4316-95(2001) 弹性材料水瓶标准规范

1.1 This specification covers requirements for molded, non-fabric reinforced, elastomeric water bottles with closure and screw stopper, generally used with hot or cold water in personal hygiene and health care. 1.2 The safe and proper use of elastomeric water bottles is beyond the scope of this specification except for the user instructions in 9.2.

Standard Specification for Elastomeric Water Bottles

ASTM D2911-94(2005) 塑料瓶的尺寸和公差标准规范

1.1 This specification covers the thread configuration and dimensions for finishes for plastic bottles with screw-type closures, having a maximum capacity of 18.9 L (5 gal) and a maximum bottle dimension of 305 mm (12 in.). Included are tolerances for bottle capacity and body dimensions.1.2 The values stated in SI units are to be regarded as the standard.1.3 The following precautionary caveat pertains only to the test methods portion, Section of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 18212;There is no similar or equivalent ISO standard.

Standard Specification for Dimensions and Tolerances for Plastic Bottles

ASTM D2911-94(2001) 塑料瓶尺寸和公差的标准规格

1.1 This specification covers the thread configuration and dimensions for finishes for plastic bottles with screw-type closures, having a maximum capacity of 18.9 L (5 gal) and a maximum bottle dimension of 305 mm (12 in.). Included are tolerances for bottle capacity and body dimensions. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 The following precautionary caveat pertains only to the test methods portion, Section 8 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1-There is no similiar or equivalent ISO standard.

Standard Specification for Dimensions and Tolerances for Plastic Bottles